NOTE ** Buell Door Company, solid and hollow core, 5-ply architectural wood veneer doors.
NOTE **
NOTE ** This section is based on the products of Buell Door Company, which is located at:
NOTE ** 5200 East Grand Avenue
NOTE ** Dallas, TX 75223
NOTE ** Tel: (800) 556-0155
NOTE ** Tel: (214) 827-9260
NOTE ** Fax: (214) 826-9163
NOTE ** Email: Buell@ix.netcom.com
NOTE ** Website: www.buelldoor.com
NOTE ** Buell Door Company is one of the nation's largest manufacturers with international distribution. This section covers only a part of their product line and stresses the inherently higher qualities of 5-ply hot-press doors. For a thorough discussion of 5-ply hot-press versus 7-ply cold press doors, including manufacturing and fabrication standards, pricing differences, bidding considerations, and warranties, see the "NOTES TO THE SPECIFIER" at the end of this section. Also see the discussion there regarding stave core doors versus SLC and particleboard core doors.
NOTE **
NOTE ** This section also includes statements for sound-rated wood doors and can also be edited for lead-lined or bullet-resistant wood doors. See Buell Door Company's Section 08212 for stile and rail wood doors and Section 08213 for high-pressure decorative laminate veneer doors.
NOTE **
NOTE ** SECTION 08211 - FLUSH WOOD DOORS, Copyright 1998, The Architect's Catalog, Inc.
PART 1 GENERAL
1.1 SECTION INCLUDES
NOTE ** Delete paragraphs and subparagraphs below not applicable to project.
NOTE ** Delete sections below not relevant to this project; add others as required.
A. Section 06400 - Wood door frames.
B. Section 08112 - Standard Steel Frames; Steel door frames.
C. Section 08212 - Aluminum Frames.
D. Section 08115 - Custom Steel Frames; Steel door frames.
E. Section 08213 - Stile and Rail Wood Doors.
F. Section 08712 - Door Hardware.
G. Section 08800 - Glass and Glazing.
H. Section 09900 - Painting and Site Finishing Doors.
I. Section _____ - _________________________.
1.3 REFERENCES
NOTE ** Delete references from the list below that are not actually required by the text of the edited section; add others as required.
A. AWI - Quality Standards of Architectural Woodwork Institute, Seventh Edition, Section 1300 and 1500.
B. NWWDA I.S.1.A - Architectural Wood Flush Doors of National Wood Window and Door Association.
C. WIC Quality Standards of Woodwork Institute of California.
D. NFPA 80 - Fire Doors and Windows, 1995 Publication.
E. NFPA 101 - Life Safety Codes.
F. NFPA 252 - Standard Method of Fire Test for Door Assemblies.
G. UL-10B - Fire Test of Door Assemblies.
H. ASTM D 5456 - Specification for Evaluation of Structural Composite Lumber Products.
I. ASTM E 152 - Methods of fire test for door assemblies.
J. ASTM E 90 - Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions.
K. ASTM E 413 - Classification for Rating Sound Insulation.
L. ASTM F 476 - Test Methods for Security of Swinging Door Assemblies.
M. ANSI/AHA A135.4 - Basic Hardboard.
N. ANSI A208.1 - Particleboard, Mat-Formed Board.
O. ANSI/HPVA HP-1 - Hardboard and Decorative Plywood.
P. NEMA LD-3 - High Pressure Decorative Laminates.
Q. Intertek Testing Services/Warnock-Hersey International - Certification Listings for fire doors.
R. ADA - Americans with Disability Act.
S. _______________________________________.
1.4 SUBMITTALS
A. Submit each item in this article according to the conditions of the Contract and under provisions of Section 01300.
B. Product Data: Manufacturer's technical data for each type of door, including details of core and edge construction, trim for openings and louvers, factory finishing specifications, and warranty.
C. Shop Drawings: Prepared specifically for this project indicating location and size of each door, veneer species, type and characteristics, elevation of each kind of door, details of construction, location and extent of hardware blocking, fire ratings, requirements for factory finishing, requirements for glass and glazing, and other pertinent data.
1. For factory-premachined doors, indicate dimensions and locations of cutouts for locksets and other cutouts adjacent to lite and louver openings.
2. Use same reference numbers for openings and details as contract drawings.
NOTE ** Delete the following paragraph if samples are not required.
D. Samples:
1. When factory finished, provide manufacturer's standard of color charts, followed by two plywood physical samples, 8-1/2 by 11 inches (215 by 280 mm) in size, illustrating wood grain, stain, color, range, and sheen for Architect's approval.
2. Architect has the option to furnish a color for the manufacturer to match.
3. For decorative laminate doors, each color, finish, and pattern are required.
4. As an option, submit construction corner samples cut away to show stile, rails, crossbanding, core, and face veneer. Samples 6 by 6 inches (150 by 150 mm) or larger.
5. Metal Louvers: Blade and frame 6 inch (150 mm) lengths for each material and finish required.
6. Frames for Lite Openings: Lite frame 6 inches (150 mm) in length for each material, type, and finish required.
7. Manufacturer's Instructions: Submit instructions regarding care of door during shipping, unloading, storage, and preparation for hanging.
E. Test Reports:
1. Submit certification letters of the following laboratory test results:
a. Stile edge screw withdrawals test and stile edge split resistance tests for fire-rated doors.
b. STC ratings for each class specified.
F. Substitutions: Submit requests for substitutions in exact accordance with Section 01600.
1.5 QUALITY ASSURANCE
A. Non-Fire Rated Wood Doors: Solid core premium grade or custom grade architectural flush wood doors; comply with the following:
1. AWI Quality Standard: "Architectural Woodwork Quality Standards" including Section 1300 "Architectural Flush Doors," of Architectural Woodwork Institute (AWI) for grade of door, core construction finish, and other requirements exceeding those of NWWDA quality standard.
2. NWWDA Quality Standard: ISI "Industry Standard for Wood Flush Doors," of National Wood Window and Door Association (NWWDA).
B. Fire Rated Wood Doors: Provide fire rated wood doors which are identical in material and construction to units tested in door and frame assemblies per ASTM E 152, and which are labeled and listed for ratings indicated by Intertek Testing Services/Warnock-Hersey, UL, or other testing and inspection agency acceptable to the authority having jurisdiction.
1. Oversize Fire Rated Wood Doors: For door assemblies exceeding sizes of tested assemblies, provide manufacturer's certificate stating that doors conform to all standard construction requirements of tested and labeled fire door assemblies except as to size.
2. Temperature Rise Rating: At stairwell enclosures, provide doors that have a temperature rise rating of 250 degrees F (121 degrees C) maximum in 30 minutes of fire enclosure.
3. Notify Architect, prior to fabrication, if fire doors indicated cannot qualify for labeling because of design, size, hardware, or other reason.
4. If material specified as fire rated and labeled can be obtained from one source, no consideration will be given to those manufacturers who are not authorized to fabricate and label items.
5. Where fire rated classifications are shown or scheduled for wood door assemblies, doors shall be installed in compliance with the requirements of "NFPA 80 Standard for Fire Doors and Windows." Attach labels permanently at eye level to hinge stile.
C. Single Source Responsibility: Provide wood doors for Sections 08211, 08212, and 08213 from a single manufacturer to ensure uniformity in quality of appearance, face veneer, finish, and construction.
1.6 DELIVERY, STORAGE, AND HANDLING
A. Handle doors at the site in accordance with AWI Section 1300-G-23 and Section G-20 "Care and Installation at Jobsite" of NWWDA I.S.-1A, as well as with manufacturer's instructions.
B. Delivery:
1. Do not deliver or install doors until conditions for temperature and relative humidity have been stabilized and will be maintained in storage and installation areas during remainder of construction period and after installation to comply with the following requirements applicable to project's geographical location:
a. Reference 7th Edition of AWI quality standard including Section 100-S-11 "Relative Humidity and Moisture Content."
2. Individually protect factory finished doors to prevent damage.
3. Deliver no doors to the building until wet construction operations are completed and dry, and weatherproof storage space is available.
4. Accept doors on site in manufacturer's packaging. Inspect for damage.
C. Storage:
1. Store doors in a clear dry ventilated space having controlled temperature and relative humidity range between 30 and 60 percent. Stack doors flat and off the floor, supported to prevent warpage.
2. Avoid extreme heat, cold, dryness, or humidity by storing doors in a closed-in building with operational HVAC system.
3. Store flat over level surface above floor on wood blocking.
D. Handling:
1. Do not walk on or place other materials on top of stacked doors.
2. Handle doors with clean gloves. Lift or carry, do not drag across one another.
3. Cover doors to keep clean and avoid discoloration with an opaque covering which does not permit light to penetrate during storage or staging. Covering must allow air circulation.
4. At time of installation the protective door wrapping is to remain in place, for door protection, until all work by other trades is completed and final inspection is finished.
5. Identify each door with individual opening numbers which correlate with designation system used on shop drawings for door frames and hardware.
1.7 FIELD MEASUREMENTS
A. Verify that field measurements are as indicated on shop drawings, prepared by the manufacturer before proceeding with factory machining.
1.8 COORDINATION
A. Contractor shall be responsible for coordinating and obtaining necessary information from Hardware and Frame manufacturers to provide door supplier with approved hardware and frame schedules with templates 60 days prior to desired delivery date of doors.
1.9 WARRANTY
A. General Warranty: Door manufacturer's warranty specified in this article shall not deprive the Owner of other rights the Owner may have under other provisions of the contract documents and shall be in addition to and run concurrent with other warranties made by the Contractor under requirements of the contract documents.
B. Warrant doors by the manufacturer to be free of manufacturing defects as follows:
1. Interior Solid Core: Life of original installation.
2. Exterior Solid Core: Two years.
3. Interior Industrial Hollow Core: Two years.
C. Exceptions to details or fire rating as shown on plans that may affect the door manufacturer's warranty, or specific fire rating, shall be brought to the attention of the Architect in writing at time of submission of shop drawings.
D. Submit written warranty agreement signed by Manufacturer, Installer, and Contractor agreeing to pay a reasonable charge to repair or replace defective doors and rehang with new doors provided the defect was not apparent prior to installation and they do not conform to tolerance limitations of referenced quality standards as follows: warped (bow, cup, or twist) more than 1/4 inch (6.35 mm) in a 42-by-84 inch (1067 by 2134 mm) section or show telegraphing of core construction in face veneers exceeding 0.01 inch in a 30 inch (0.25 mm in a 762 mm) span.
E. Contractor's Responsibilities: Replace or refinish doors where Contractor's work contributed to rejection or to voiding of manufacturer's warranty.
PART 2 PRODUCTS
2.1 MANUFACTURERS
NOTE ** Delete one of the two paragraphs below. The first is to specify Buell Door Company and those manufacturing equal products, the second is to specify Buell Door Company exclusively.
A. Acceptable Manufacturers: Products and materials of the following listed manufacturers are acceptable only if specific products and materials can evidence exact compliance with requirements of Contract Documents and these Specifications.
1. Buell Door Company
2. Algoma Hardwoods, Inc.
3. Eggers Industries, Architectural Door Division
4. Weyerhaeuser Company
B. Provide flush wood doors as manufactured by Buell Door Company, 5200 East Grand Avenue, Dallas, TX 75223: ASD. Tel: (800) 556-0155 or (214) 827-9260, Fax: (214) 826-9163, Email: Buell@ix.netcom.com; Website: www.buelldoor.com
C. Requests for substitutions will be considered in accordance with provisions of Section 01600.
NOTE ** Delete paragraph above or below; coordinate with Division 1 requirements.
D. Substitutions: Not permitted.
E. Provide all wood doors from a single manufacturer.
NOTE ** Delete "AND TRANSOM PANEL" in the Article title below if transom panels are not required for the project.
2.2 DOOR AND TRANSOM PANEL TYPES
A. Flush Interior Doors:
NOTE ** Select thickness, type, and other characteristics from subparagraphs below. Delete those not required for the project.
1. Thickness: 1-3/4 inches (44 mm).
2. Thickness: 2-1/4 inches (57 mm).
3. Type: Solid core.
4. Type: Hollow core.
5. Fire rated.
6. Acoustic rated.
7. Lead lined.
8. Bullet resistant construction.
NOTE ** Select thickness below as required, deleting thickness not required for the project.
B. Flush Exterior Doors:
1. Thickness: 1-3/4 inches (44 mm).
2. Thickness: 2-1/4 inches (57 mm).
3. Type: Solid core.
NOTE ** Delete paragraph below if not required for the project.
C. Transom Panels: Match face veneer with continuous match and other door characteristics indicated.
NOTE ** Delete "AND TRANSOM PANEL" in the Article title below if transom panels are not required for the project.
2.3 DOOR AND TRANSOM PANEL CONSTRUCTION
NOTE ** Select construction(s) from paragraphs below. Delete those not required for the project.
A. Core (solid, non-rated): AWI Section 1300-S-7, Type PC-5 bonded particleboard.
B. Core (solid, fire rated): AWI Section 1300-S-13, Type S (FD 1 1/2, FD 1, FD 3/4, FD 1/2, FD 1/3).
C. Core (solid, acoustical): AWI Section 1300-S-13, Type SR.
D. Core (solid, lead lined): AWI Section 1300-S-13, Type LL.
E. Core (solid, electrostatic shielded): AWI Section 1300-S-13, Type ES.
F. Core (hollow): AWI Section 1300-S-15, Type IHC institutional.
2.4 FLUSH DOOR FACING
NOTE ** Select and edit one or more of the following paragraphs as required for the project.
A. Interior Natural Wood Veneer Doors:
NOTE ** If pre-selection of a particular veneer flitch is made, then designate "veneer to be furnished from Veneer flitch approved by the Architect." Use caution when specifying plain slice Natural Birch; the term "natural" or "unselected" Birch means the veneer may contain both the sapwood, or white portion, as well as the heartwood, or dark portion, of the tree in unrestricted amounts. The heartwood of the birch tree varies in color from medium to dark brown or reddish brown, while the sapwood portion of the tree is near white. "Select White Birch" should be specified if veneer is to be uniform in color with no contrasting dark brown portion in unrestricted amounts.
1. Veneer Cut and Specie: ____________________.
2. Veneer Thickness and Grade: 1/40 inch (0.64 mm) before sanding minimum with quality characteristics of AWI Section 1300 and 200-S-9 Panel Products "A" Grade veneer face with edge glued joints.
3. Veneer Leaf Match: Book match grain.
4. Veneer Face Match: Running match.
5. Transoms: Continuous matched.
6. Pairs and Sets: Provide pair matching and set matching for pairs of doors and for doors hung in adjacent sets.
7. Door Thickness: 1-3/4 inches (44 mm).
B. Interior Hardwood Composite Veneer Doors:
NOTE ** For projects requiring door veneer faces that are defect free (without small burls, occasional pin knots, worm holes, color streaks, or spots that are natural characteristics of some veneer species), hardware composite veneer should be specified. They are produced by converting bland African wood into a custom-patterned veneer through a dye and mold system which allows for the production of a wide range of conventional veneers that are unparalleled for consistency in grain and color. Veneer species are available in unlimited quantity for add-ons to existing installations. The industry leader is Brookside Veneers, Ltd.; 1-800-887-5878.
1. Face Veneer: Brookline hardwood composite veneer no. _____.
a. Specie: _______________________________.
2. Veneer Thickness: 1/42 inch (0.60 mm) before sanding.
3. Veneer Leaf Match: Slip match.
4. Veneer Face Match: Running match.
5. Transoms: Continuous matched.
6. Pairs and Sets: Provide pair matching and set matching for pairs of doors and for doors hung in adjacent sets.
7. Door Thickness: 1-3/4 inches (44 mm).
NOTE ** A description of the sketch face and the manufacturer should be specified (e.g., Sapele Pommele, Birdseye Maple, etc./Herring Bone, Reverse diamond, sunburst, box sketch, simulated Stile and Rail of WD-1 with herring bone insert panels of WD-3, produced by, e.g., Architectural Forest Products; Two Rivers, WI 54241).
NOTE **
NOTE ** Sketch face veneers are often used where aesthetic appearance of door faces impacts design effect of an area, such as the lobby, entrance to the board room, executive offices, etc. Many interesting exotics are commercially available as veneer and can be an economical way to "jazz up" a project. Sketch face design is the responsibility of the designer and should be illustrated in the door elevations of the project plans. Buell Door Company will provide guidance for sketch match face designs.
C. Exotic Veneer/Sketch Face Match: Fabricate sketch face doors with sketch face veneers that comply with the designer's dimensioned door elevations detailed in the project plans, showing veneer component species, grain direction, and finish.
NOTE ** Polyvinyl chloride thermoplastic sheet veneer is specified extensively in hospitals, nursing homes, clinics, schools, airports, etc., as a protective surfacing material for interior walls and kick plates on doors. Polyvinyl chloride thermoplastic sheet offers more resistance to impact, chemicals, and general abuse than high pressure laminates. Specify polyvinyl chloride thermoplastic door facings in high traffic areas to minimize damage to door surface and edges.
NOTE **
NOTE ** The leading manufacturer is IPC Door and Wall Protection Systems, Muskogee, WI (1-800-222-5556).
NOTE **
NOTE ** High-impact polyvinyl chloride thermoplastic as specified in the following paragraph, should not be used to face exterior doors.
D. High-Impact Polyvinyl Chloride Thermoplastic Veneer Doors:
7. Edge Trim: Bevel both edges of door 1/8 inch in 2 inches (3.1 mm in 51 mm) and laminate (clad) edges with same PVC material as the face, using hot-melt glue that is cured under heat and pressure for permanent adhesion.
8. Door Thickness: 1-3/4 inches (44 mm).
E. Interior Painted Finish Doors:
1. Hardboard: ANSI/AHA A135.4, Class 1 - tempered, type SIS hardboard 1/8 inch (3 mm) thick, for paint finish.
2. MDO: Medium Density Overlay non-directional, 0.015 inch (0.38 mm) face veneer over standard hardwood crossband, AWI Grade 1. International Paper "Uniwood" product 10306 Luxcell face is acceptable for interior application.
3. Close Grain Hardwood Veneer: Minimum B or sound grade, 1/50 inch (0.51 mm) thickness at 12 percent moisture content.
NOTE ** An example of specie and veneer cut in the following subparagraphs would be "Paint Grade Birch, Rotary cut."
a. Specie: _______________________________.
b. Veneer Cut: _______________________________.
4. Door Thickness: 1-3/4 inches (44 mm).
NOTE ** Exterior wood veneer doors in the article below are the same as specified under Interior Wood Doors. High pressure decorative laminate veneer should not be used to face exterior doors. To maintain warranty, comply with finishing and other protective measures specified in Part 3 - EXECUTION.
F. Exterior Wood Veneer Doors:
2.5 FABRICATION
NOTE ** Select and edit the following items to suit project requirements.
NOTE **
NOTE ** The 'building standard' doors are usually more accurately specified as AWI Custom Grade, the highest grade used most of the time, which is suitable for most projects. AWI Premium Grade doors are specified when the highest degree of control over the quality of materials specified is required, often in conjunction with architectural panels and other related doors. The AWI Custom Grade allows 'A' grade veneer faces and running match, while Premium Grade requires 'AA' grade veneer faces and balance match.
A. Grade: Custom.
B. Grade: Premium.
C. Construction: AWI 1300; PC-5, for Wood Veneer Doors.
D. Non-Rated and 20 Minutes Fire-Rated Doors:
1. Core: Mat Formed Wood Particle Board, Grade 1-L-2; 28-32 pcf (0.448 to 0.513 g/cc) density meeting requirements of ANSI A208.1.
2. Bonding: Stiles and rails bonded to core using Type I glue and sanded as a unit prior to applying veneers. Drop in core is not acceptable.
3. Crossbands: Dried to 6-9 percent moisture content, minimum 1/16 inch (1.58 mm) thick spliced hardwood with no voids or defects, extending full width of doors with grain at right angles to face veneer.
4. Stiles: 1-1/2 inch (38 mm) deep before fitting. 1-1/8 inch (28.5 mm) minimum after trimming, 2 ply construction without fingerjoints, consisting of 1/2 inch (12.7 mm) thick outerband specie matching or compatible with face veneer and 1 inch (25.4 mm) thick innerband of TimberStrand Laminated Strand Lumber (LSL) by Trus Joist MacMillan or hardwood at mill option. The vertical edges on particleboard core doors will require a minimum testing rating as follows:
a. 525 pounds (2.335 kN) per the NWWDA TM-5 "Split Resistance."
b. 930 pounds (4.137 kN) per the NWWDA TM-8 "Hinge Loading Resistance."
c. 1,000 pounds (4.448 kN) per the NWWDA TM-10 "Screw Holding Capacity" test reports.
5. Rails: 1-1/8 inch (28.5 mm) after trimming; Laminated Strand Lumber (LSL) by Trus Joist MacMillan or hardwood at mill option.
6. Pairs: Use ITS/Warnock-Hersey or UL 20 minute labeled pairs with fire retardant stiles without steel channels covering meeting edges on a pair measuring 4 feet by 10 feet (1.219 by 3.048 m) maximum each leaf.
E. Fire Rated, 45, 60, and 90 Minute Doors: AWI 1300-S-4-13. Comply with requirements of Paragraph 1.02 and the following minimum requirements. Test labeled doors in conformance with UL or ITS/Warnock-Hersey International, NFPA 252, and ASTM E 152.
1. Core: Door manufacturer's standard non combustible mineral core; incombustible, asbestos-free mineral composition, engineered to meet labeling requirements.
2. Stiles and Rails: Manufacturer's standard sizes to meet fire rating, bonded to the core, complying with the following:
a. Stile Edge Screw Withdrawals: Minimum 740 pounds (3.292 kN) when tested in accordance with ASTM D 1037.
b. Stile Edge Split Resistance: Minimum 750 pounds (3.336 kN) when tested in accordance with ASTM D 143 (modified); vertical edge solid, laminated, or veneered of same species as visible surface. Reinforce hinge edge on all fire doors to accommodate full mortise hinges and to provide additional screw holding power when hinge is installed, unless specified otherwise.
3. Crossbands: Dried to 6-9 percent moisture content, minimum 1/16 inch (1.58 mm) thick spliced hardwood with no voids or defects, extending full width of doors with grain at right angles to face veneer.
4. Blocking: No through-bolting is allowed for attaching finished hardware. Refer to Section 08700 for hardware requirements. Provide composite blocking designed to maintain fire resistance of door but with improved screw-holding capacity "as required by specified hardware" with one or all of the following options:
a. 5 inch (127 mm) top rail blocking to accommodate surface mounted closer attached with wood screws.
b. 5 inch (127 mm) bottom rail blocking to accommodate hardware attachment not unlimited undercutting.
c. 5 inch by 18 inch (127 by 457 mm) lockblocks for locksets and exit devices.
d. Blocking for flushbolts and vertical rod exit devices.
NOTE ** In the following paragraph, caution should be used when specifying concealed vertical rod fire exit devices on pairs of doors in high traffic areas in buildings where doors are subject to abuse. When doors are machined for this hardware, the mortise cut-outs at the top and bottom latch area of the door have a 3/32 inch (2.4 mm) face material remaining. Subsequent breakage can occur which, if not repairable, can lead to expensive replacement of the doors.
NOTE **
NOTE ** There is one exception. This is not a concern when specifying the Adams Rite 3900 Series because the mortise cutout in the top of the door for the top rod only exit device is only 1/4 inch diameter. Thus the door strength is not affected and would have the same strength as a door with surface-applied vertical exit device rods.
5. Pairs: Provide 20, 45, 60, and 90 minute single swing or double egress fire rated doors "as required by specified hardware." Where exit devices are required, comply with one or more of the following:
a. Non-Rated and 20 Minute Fire Rated Doors:
1) Single Swing or Double Egress doors up to 8 feet by 10 feet (2.438 by 3.048 m) opening size, manufacture doors to receive:
a) Surface-applied vertical rod fire exit devices; no metal edges or astragals required.
b) Concealed vertical rod exit devices require 5 inch (127 mm) Georgia-Pacific Firestop or approved equal, with Natural matching full length wood edge meeting stiles, no finger joints, 1/2 inch (12.7 mm) maximum width of wood after trim, no metal edges or astragals required.
c) Surface-applied top vertical rod only exit devices: Adams Rite Mfg. or approved equal; no metal edges or astragals required.
d) Concealed top vertical rod only exit devices: Adams Rite Mfg. or approved equal; no metal edges or astragals required; maximum size 8 feet by 8 feet.
b. 45,60,and 90 Minute Fire Rated Doors:
1) Single Swing or Double Egress doors up to 8 feet by 8 feet (2.438 by 2.438 m) opening size:
a) Manufacture doors to receive surface applied vertical rod fire exit devices with Georgia-Pacific fire door components or approved equal, having Natural matching wood edge meeting stiles, 2 ply construction consisting of an innerband of fire retardant composition material of Georgia-Pacific Firestop or approved equal, outerband natural hardwood matching or compatible to face veneer.
b) Double egress requires through-bolting or "sex" bolts at latching points; surface top rod only devices must be through-bolted (sex bolts). Metal edges and overlapping astragals are available, but not required.
NOTE ** For 20-minute fire-rated door pairs with concealed vertical rod exit devices, no thermal pins or strikes should be used. On 45- or 60-minute fire-rated door pairs with concealed vertical rod exit devices, the pins are located horizontally and no floor strikes are required. For 90-minute door pairs only, the Adams Rite system requires a steel strike plate for each door, located in the floor and measuring 3/8 inch (9.5 mm) in diameter and 1/2 inch (12.7 mm) deep, for thermally activated pins of 3/8 inch (9.5 mm) diameter located in the bottom of the door rail. The pin is not visible once installed when in the bottom of the door.
NOTE **
NOTE ** This hardware must be supplied by the door manufacturer with the Adams Rite Mfg. concealed or surface mounted top rod only design or approved equal.
2) Single Swing or Double Egress doors up to 8 feet by 8 feet (2.438 by 2.438 m) opening size:
a) Concealed top vertical rod only exit devices: Adams Rite Mfg. or approved equal.
b) Natural matching wood edge meeting stiles, Georgia-Pacific Firestop II System or approved equal.
NOTE ** The following are options; delete those not required for project.
c) 48 inch (1.219 m) protection plate of metal, stainless steel, or IPC high-impact PVC.
d) Metal hinge protectors.
3) Single Swing up to 8 feet by 9 feet (2.438 by 2.743 m) opening size:
a) 5 inch (127 mm) metal U channel on lock stiles, primed or veneer wrapped with natural wood. Channel may not be mortised. Von Duprin or approved equal.
b) 5 inch (127 mm) wide edge meeting stiles, Georgia-Pacific Firestop or approved equal.
6. 45 Minute Full Lite Door Pairs up to 8 feet by 9 feet (2.438 by 2.743 m) opening size: Manufacture using Georgia-Pacific fire door components or approved equal, with 3/4 inch (19 mm) transparent composite light panel manufactured by SuperLite Panel II - 45 as distributed by O'Keefe's Inc., maximum clear view area of 2,638 sq. in. (1.701 sq. m) per leaf.
F. Security Rating: ASTM F 476, Grade 40.
G. Individually polybag all doors.
NOTE ** Utilize the following paragraphs when required by the project.
H. Door and Transom Combination:
1. Wood Grain Patterns: Continuous veneer match as per NWWDA I.S.-1 Standards.
2. Top Rail of Door and Bottom Rail of Transom: Full width; matching species lumber or veneered with same face veneer species.
I. Acoustically Rated Construction: AWI 1300 G-10-SR.
1. Core: Manufacturer's standard sound dampened core construction to achieve a sound transmission class rating of not less than 41 for a door thickness of 1-3/4 inches (44 mm), certified by the manufacturer to be based on tests conducted at an independent testing agency in accordance with ASTM E 90 and E 413, as operating units.
2. Vertical Stiles: Minimum 1-3/8 inch (34.9 mm) minimum after trimming, 2 ply construction without fingerjoints, consisting of 5/8 inch (15.8 mm) thick mill option hardwood.
4. Top Rail: 1-3/8 inch (34.9 mm) minimum mill option hardwood.
5. Crossbands: Full width of door with grain running horizontally, tapeless sliced without voids.
6. Face Veneer: As specified, laminated to crossband and edges.
7. Bonding:
a. Core to Stiles, Rails, and Blocking: Type I adhesive; sand prior to assembly of face veneers.
b. Face Veneers and Crossband to Core and Edges: Type I adhesive by hot press process.
8. Door equipped with concealed retracting bottom seal and perimeter concealed door gasketing.
J. Lead Lined Construction: AWI 1300-S-3(LL).
1. Core: Manufacturer's standard construction; one piece lead sheet or sheets extending to all four edges; total door thickness 1-3/4 to 2-1/2 inches (44 to 63 mm).
2. Face Veneer: Same as non-lead lined doors.
3. Stile and Rails:
a. Vertical Edges: 1-1/8 inch (28.5 mm) minimum hardwood; solid, laminated, or veneered same species visible surface. No visible joints permitted.
b. Top and Bottom Rails: 1-1/8 inch (28.5 mm) minimum mill option hardwood.
c. Securely bond vertical edges and rails to core.
K. Stave Lumber Core Construction:
1. Core: Construct stave core using random length kiln dried (6 to 9 percent moisture content) wood blocks
2. Stagger core and joints tightly in adjacent rows, all blocks securely edge glued together under pressure.
NOTE ** To specify structural composite lumber (SCL) core such as TimberStrand LSL core by Trus Joist MacMillan, approved by the AWI and NWWDA associations as a preferred substitute in lieu of stave core, include the following.
L. Structural Composite Lumber Core Construction: TimberStrand LSL by Trus Joist MacMillan.
1. Core: TimberStrand LSL or other structural composite lumber (SCL) in accordance with ASTM D 5456; uniform density of 38 pcf (0.61 g/cc), with minimum target MOR at 6,000 psi/MOE 1.3 x 10^6 psi.
M. Institutional Hollow Core: Phenolic impregnated honeycomb with two woven interlocking cells; two lock blocks.
N. Bullet Resistant Wood Door Construction: Solid core consisting of ArmorCore Bullet Resistant Fiberglass Armor as shown in the drawings and manufactured by Waco Composites, Inc., Waco, TX or ArmorTex Bullet Resistant Fiberglass as manufactured by Safeguard Security, San Antonio, TX; veneer or plastic laminate as selected.
NOTE ** Select protection level required for project from subparagraphs below; delete those not required for project.
1. Level I - Class 1, Medium power small arms NIJ HA-1/4 inch thick.
2. Level II - Class 2, High power small arms NIJ H-5/16 inch thick.
3. Level III - Class 3, Super power small arms NIJ IIIA-7/16 inch thick.
O. Flush Doors with Flat Panels:
1. Grade: Premium.
2. Construction: 5 ply, 20 minute rated.
3. Core: Solid particleboard.
4. Panel: 7/8 inch (22.2 mm) medium density fiber board laminated with 7/16 inch (11.1 mm) molding on each side.
P. Flush Doors with Face Reveals:
1. Fabricate with identical reveals measuring up to 1/4 inch (6.3 mm) in width and maximum 3/64 inch (1.2 mm) in depth on both sides of the door.
2. Comply with designer's dimensioned door elevations detailed in project plans.
3. Approved by door manufacturer's Fire Door labeling authority.
4. In no case shall the area grooved exceed 3 percent of the area of the face.
2.6 FABRICATION TOLERANCES
A. Size:
1. Thickness: Plus or minus 1/16 inch (1.6 mm).
2. Height: Plus or minus 1/16 inch (1.6 mm).
3. Width: Plus or minus 1/32 inch (0.8 mm).
B. Squareness: Diagonal measures not to exceed 1/16 inch (1.6 mm).
C. Hardware Location: Plus or minus 1/32 inch (0.8 mm).
2.7 ADHESIVE
A. Facing Adhesive: Type I - waterproof.
2.8 ACCESSORIES
A. Lite and Louver Details:
1. Field glaze all lite openings.
2. Install lite openings for non-rated wood doors with manufacturer's standard wood beads. Cut lite openings and install wood beads permanently on one side, tacked loose on other side.
3. Furnish lite openings for fire doors with either flush wood veneered lite bead or primed metal vision panels (veneered covered metal vision panels optional) as per the manufacturer's approvals. Flush wood veneered lite beads or metal vision panels shall be approved by Intertek Testing Services/Warnock-Hersey International for use in 20, 45, 60, and 90 minute doors.
4. Glazing Stops:
NOTE ** Insert wood species below to be same as door facing. Select channel shape, type of corners, and tamper proof screws as required for project.
a. Wood Species: ________________________, with metal clips for rated doors.
b. Channel Shape: Roll steel.
c. Channel Shape: Aluminum.
d. Corners: Mitered.
e. Corners: Butted.
f. Prepare for countersink style screws.
g. Prepare for countersink style tamperproof screws.
NOTE ** Wood louver are manufactured by wood door manufacturers. Metal louvers are not. Metal louvers can be specified in this section or elsewhere. Coordinate with door schedule.
5. Wood Louvers: Manufacturer's standard construction.
a. Same species lumber as face veneer.
b. Factory installed using manufacturer's standard method.
NOTE ** Select type of slat from subparagraphs below.
c. Slat Type: Single slat.
d. Slat Type: V-slat chevron.
NOTE ** Specify manufacturer and model number below if metal door louvers are required for the project.
6. Metal Louvers: _________________________________.
7. To maintain warranty, do not cut light exceeding maximum 40 percent of height and 5-1/2 inches (140 mm) from door edge and face hole prep-of lock set.
B. Applied Molding:
1. Species: Matching or compatible with face veneer.
2. Selected from manufacturer's standard profiles approved by Architect.
3. Apply molding to door face with finishing nails; putty holes so they are not visible.
2.9 PREFIT AND PREMACHINE
A. Prefit doors at the factory with the following clearances:
1. 1/8 inch (3.1 mm) on top and hinge edges.
2. 1/8 inch (3.1 mm) on lock edge of single doors
3. 1/16 inch (1.6 mm) per leaf on pair meeting edges.
4. Bevel both edges of door 1/8 inch in 2 inches (3.1 mm in 51 mm).
5. Bottom: 1/4 inch (6.3 mm) above floor or threshold, except where undercutting is indicated. Specific bottom clearance is shown on door schedule.
B. Premachine doors for finish hardware.
1. Furnish wood door manufacturer an approved frame schedule (including all hardware locations), approved hardware schedule (including all necessary hardware templates), and an approved door schedule.
2. In lieu of these three schedules, furnish door manufacturer one coordinated schedule showing all data relative to frame, hardware, and door information.
C. Make cutouts for glazing at the factory. Allow 5-1/2 inches (140 mm) minimum from cutout to mortised hardware items.
D. Contractor is responsible for boring pilot holes, wood screw holes, mounting holes for face plates, and other surface applied hardware listed on the hardware schedule, unless special arrangements are made with the door manufacturer prior to submittal of shop drawings to the Architect.
E. Kickplates, push plates, stretcher plates, edge guards, and other protective hardware shall be furnished by the hardware supplier or Contractor and installed in the field.
2.10 PREFINISHING
NOTE ** Select type of finish to comply with project requirements.
A. General: Comply with referenced quality standards requirements for factory finishing.
B. Transparent Finish: Comply with requirements indicated for grade, finish system, staining effect, and sheen:
1. Grade: Custom.
2. Finish: Manufacturer's standard finish with performance requirements comparable to AWI System TR6 catalyzed polyurethane.
3. Staining: Match approved sample for color.
4. Effect: Open-grain finish.
5. Sheen: Semigloss, 60 percent.
NOTE ** The following subparagraph is an optional method of specifying a transparent finish; if used, delete the subparagraphs above.
6. Match Buell Door Co. Finish Sample No. __________.
C. Opaque Finish: Comply with requirements indicated for grade, finish system, color, and sheen:
1. Grade: Custom.
2. Finish: Manufacturer's standard finish with performance requirements comparable to AWI System OP-6 catalyzed polyurethane.
3. Color: Match approved sample for color selected from manufacturer's standard colors.
4. Sheen: Semigloss, 60 percent.
PART 3 EXECUTION
3.1 EXAMINATION
A. Examine doors and door frames to verify that frames have been installed as required for proper hanging and operation of doors.
1. Frames must comply with indicated requirements for door type, size, location, and swing characteristics, and have been installed with plumb jambs and level heads.
2. Doors with apparent defects should not be hung.
3. Notify the Architect in writing of conditions detrimental to proper installation and operation of wood doors.
4. Do not proceed with installation until unsatisfactory conditions have been corrected.
5. Proceeding with installation shall be considered as acceptance of door and frame conditions.
3.2 INSTALLATION
A. Field Finishing: Place door in a horizontal position, thoroughly sand all surfaces with hand block and 150-180 grit sand paper to remove handling marks and raised grain to prevent blotchy appearance. Seal top and bottom rails.
B. Adjusting and Cleaning: Doors shall swing in their respective frames free of hinge binding or improper latching.
1. Trim non-rated door width by cutting equally on both jamb edges. Trim height by cutting bottom edges to a maximum of 3/4 inch (19 mm).
2. Trim fire rated door height at bottom edge and in accordance with fire rating requirements.
3. Rehang or replace doors which do not operate freely as directed by the Architect.
4. Seal cut surfaces after fitting and machining.
5. Leave protective door wrappings in place until all work by other trades is complete and final inspection is finished.
6. Furnish Owner with instructions on cleaning and maintaining doors.
C. Exterior Doors:
1. Provide aluminum flashings full thickness and width of doors.
a. Top rail.
b. Bottom rail.
c. Sill of glazed openings.
2. Apply three coats of marine finish such as Bruning Paint Super Marine Spar Varnish 508-14, a phenolic alkyd resin varnish.
3. Protect door with canopy.
4. Failure to provide these measures can void manufacturer's warranty.
D. Hardware: For installation, see Section 08710.
3.3 INSTALLATION TOLERANCES
A. Conform to AWI for requirements for fit and clearance tolerances.
3.4 ADJUSTING
A. Adjust work under provisions of Section 01700.
B. Adjust doors for smooth and balanced door movement.
3.5 FIELD QUALITY CONTROL
A. Architect may require one randomly selected door to be used for testing for Contract Document compliance. Test will consist of cutting door up to expose blocking, stiles and rails, core bonding, and veneer cross-section.
B. Tests may also be conducted for quality and type of factory finishing.
C. If tested samples show non-compliance with Contract Document requirements, all doors provided under this Section shall be replaced at no addition to Contract Sum or extension of Contract time.
NOTE ** Provide schedule below when door and frame schedules are not described on drawings. The schedule should identify various types or categories of doors and associated frames, fire ratings if any, hardware sets, etc.
3.6 SCHEDULE
NOTE ** NOTES TO THE SPECIFIER:
NOTE **
NOTE ** This specification for flush wood doors has been prepared for use by architects specializing in the commercial and institutional markets. It depicts 5-ply architectural wood veneer doors and 3-ply high-pressure decorative laminate doors and is in strict compliance with AWI Quality Control Standards, 7th Edition.
NOTE **
NOTE ** Buell Door Company, AWI members, and the other manufacturers listed, recognize the superiority of 5-ply doors from a quality control, aesthetic, and functional point of view. Manufacturers offering 5-ply doors provide the highest degree of technical expertise, premachining, prefinishing, and coordination; they are, in general, qualified to handle architectural grade projects.
NOTE ** Buell Door Company and many of the other architectural manufacturers acknowledge that a large percentage of the marketplace, whether due to budget or other considerations, may allow approval of 7-ply door manufacturers in their wood door specifications. Because there are wide variations in 7-ply door construction, the specifier is cautioned to insist that all approved manufacturers comply with the performance requirements of these specifications as they relate to product material and fabrication methods. When this is done, it minimizes the chances of inferior quality doors being supplied on a project which do not comply with the intended performance standards and aesthetic requirements. By maintaining important performance parts of the specification, the specifier can be assured that suppliers will be bidding doors of equal quality level.
NOTE ** Why specify only 5-ply, hot press construction? Because in the bidding process, when 5-ply and 7-ply manufacturers are both approved, the door distributors will only bid the lowest quality 7-ply door possible. Door pricing, not door quality, becomes the primary consideration. Subsequently, the lowest grade of commodity 7-ply doors get furnished while the better quality 5-ply architectural grade door is never seriously considered.
NOTE **
NOTE ** Because of a significant price spread between 5-ply and 7-ply doors, no distributor will risk losing a job by bidding the 5-ply door. This price differential will always exist because there are real cost differences in the quality of material and manufacturing processes of the two door types.
NOTE ** Consequently, to protect market share, some 5-ply door manufacturers also produce a lower quality 7-ply door that may have an imported 3 ply door skin made in Asia with a thin 1/100 inch veneer face, priced lower to distributors. This enables them to compete in the market with doors manufactured by commodity 7-ply manufacturers. When 5-ply and 7-ply manufacturers are both specified, it is the 5-ply manufacturer's 7-ply lower quality door that will be bid and furnished. Chances of 5-ply architectural grade doors being furnished are negligible.
NOTE **
NOTE ** If assurance of door quality is important, the specification should allow for only 5-ply hot press construction. Once doors are installed, it not easy to reject poor quality doors, due to delays in building completion and occupancy.
NOTE ** How do 5-ply and 7-ply manufacturers differ in manufacturing methods and door component parts? First, all reputable 5-ply door manufacturers conform to the same specifications regarding hardwood rails and stiles, bonded-to-the-core construction, hot-press lamination, tight exterior veneer tolerances, and other quality-driven parameters.
NOTE **
NOTE ** Second, unlike 5-ply doors, there are wide variances in 7-ply door construction. Some use softwood finger-jointed rails and stiles, others use hardwood. Skin thicknesses and glue grades vary. Some 7-ply doors have drop-in cores, while others are bonded-to-the-core. Other differences abound.
NOTE ** Third, 5-ply manufacturers are more custom-driven versus some 7-ply manufacturers who are volume-driven, importing most of their skins from the Orient. So, while both 5-ply and 7-ply doors can be constructed from most any species of wood, a 7-ply door in a non-standard wood species will require a much longer lead time.
NOTE **
NOTE ** Fourth, since 5-ply are usually custom-built, there is greater flexibility in making or matching veneer patterns. Even door edges can be species-matched to the door face if requested. Conversely, 7-ply manufacturers purchase veneers already assembled to the underlying crossband layers, so grain-matching can be limited. Some 7-ply door manufacturers do not provide pair matching for all their door sizes, especially full height doors.
NOTE ** Why is surface veneer thickness important? A thicker surface veneer (typically 1/40 of an inch compared to 1/100 of an inch on some 7-ply doors) is especially important if the door is to "prepped" or sanded in the field for finishing or repair. It is very easy to sand through a thin exterior veneer and expose the crossband, ruining the door. In addition, thinner veneers often must be prepared differently to avoid checking or splitting when treated or finished.
NOTE **
NOTE ** With thicker veneers, however, these problems are avoided. In addition, thicker veneers exhibit greater grain depth and definition in the staining and finishing process. In other words, for wood doors, beauty does depend on how deep the skin really is.
NOTE ** What about differences in fabrication? Exterior skins for 5-ply doors are cut directly from the tree and assembled, providing complete flexibility in veneer cut and design. In contrast, because 7-ply skins are so thin, they are first assembled to the crossbands and shipped to the manufacturer as a single piece, thereby reducing or eliminating veneer design flexibility.
NOTE **
NOTE ** Also, 5-ply door manufacturers normally manufacture every component of the door, giving them complete control over quality and manufacturing tolerances. On the other hand, 7-ply door manufacturers typically assemble purchased door parts, limiting manufacturing precision as well as flexibility.
NOTE ** How does laminated strength compare? The layers of 5-ply doors are hot-press bonded to cores that have been banded with and glued to hardwood rails and stiles, whereas 7-ply doors are cold-press bonded at a significantly lower pressure. Higher pressure plus heat during the bonding process greatly reduces the chance of delamination. As proof, consider that most 5-ply doors are backed with a lifetime warranty; some 7-ply doors come with a limited 5-year warranty with surcharges to upgrade to a lifetime warranty with no change in construction methods or material.
NOTE ** What does "bonded-to-the-core" mean and is it important? Bonded-to-the-core means that the door rails and stiles are glued or bonded to the door core before the crossband and surface veneers are added. Doors constructed this way are stronger and more rigid than with other techniques, increasing the useful life of the door.
NOTE **
NOTE ** Bonding to the core also enables the manufacturer to sand all the parts together as a unit, reducing problems such as "telegraphing" (a frame-joint offset that shows on the surface of the door after assembly). Virtually all 5-ply doors are bonded-to-the-core; many 7-ply doors are not.
NOTE **
NOTE ** Results of hinge loading resistance tests illustrate that average loading resistance of doors with stiles bonded-to-the-core is higher than doors with non-bonded wood door stiles.
NOTE ** Do all door manufacturers have the same finishing capabilities? As for color matching, that depends on the manufacturer. For instance, 5-ply manufacturers can mix up virtually any color and custom match it to an architectural control sample. Some 7-ply manufacturers, however, are limited in that they offer only a normal "standard grade" of finish consisting of their standard colors, topcoats, and finishing techniques. They may not be able to offer a "select" grade of finishing that permits color selection special sheens other than their standards. Also, they are not likely to offer "super grade" of finishes requiring high aesthetic characteristics such as bleached finishes, filled finish special sheens other than their standards, and special effects such as glazing, toning, and shading.
NOTE **
NOTE ** Use caution when specifying 7-ply manufacturers since listing a manufacturer deems the manufacturer's standard finish as acceptable.
NOTE ** What type of warranty is available? In specifying a 5-ply solid core wood door, expect and accept no less than a Full, Unlimited Lifetime Warranty. This means the following:
NOTE **
NOTE ** 1. Duration of implied warranties may not be limited. Warranty service must be provided to anyone who owns the product during its useful life, subsequent buyers notwithstanding.
NOTE ** 2. Warranty service must be free of charge, including reasonable cost of removing, returning, and reinstalling the product.
NOTE ** 3. At the consumer's choice, a replacement or full refund will be provided if, after a reasonable number of attempts, the problem is not corrected.
NOTE ** 4. The consumer is not required to perform any unreasonable duty in order to receive service, other than notifying the manufacturer that service is needed.
NOTE **
NOTE ** With some 7-ply door manufacturers, expect only a Limited 1- to 5-Year Warranty with an optional "lifetime" warranty for a higher price but with no change in door construction.
NOTE ** What about stave core doors? Stave core doors are inferior to either structural composite lumber (SCL) such as TimberStrand LSL core doors by Trus Joist MacMillan, or particleboard core doors, and should be eliminated from door specifications for the following reasons:
NOTE **
NOTE ** 1. In most cases, specs for stave core doors can be attributed to either an older spec that has not been updated or the owner/architect's misinformation regarding the many advantages of specifying a different alternative core when there is no obvious benefit to be gained by using stave core.
NOTE ** 2. There is a very limited supply of good quality stave core with proper moisture content. Some regions utilize softwood species, such as pine, while others utilize hardwoods like aspen and basswood. In all cases, input materials are low grade cutbacks from other processing steps. Most stave core is made from the residue of wood products manufactured for other purposes, such as furniture. Consequently, it is subject to "peak and valley" production. No manufacturer currently makes stave core as a primary product. It is not uncommon for an architectural door manufacturer to be quoted a lead time of three months for a truck load of stave core, with a cap on the amount he can order during a given year.
NOTE ** 3. With stave core doors, the risk of defects on door face veneers is significantly greater than that of either particleboard or TimberStrand LSL core doors. AWI points out that doors constructed by using an alternative door core substrate have greater dimensional stability.
NOTE ** 4. By using one of the alternative door core substrates, the building owner can substantially reduce maintenance costs because of door replacements due to defects developing outside the manufacturer's stipulated warranty -- defects due to dimensional instability of the stave cores exposed to extreme relative humidity.
NOTE ** 5. NWWDA tests show screw holding and hinge load strength is more dependent upon the species and the size of the wood stile, not of the core itself. If necessary to meet hardware requirements, a particleboard core door can be further strengthened with blocking and extra wide top and bottom rails. Structural composite lumber (SCL) core does not require extra wide top and bottom rails.
NOTE ** 6. Security alone is not justification for specifying stave core because it has no higher security grade rating than particleboard core. Per ASTM F 476, even particleboard core doors carry the highest security rating, Grade 40. Door Impact Tests conducted by Intertek Testing Services/Warnock-Hersey International subject a door to impacts at the center of a door using a 99 pound ram. Two impacts are performed for each ascending grade from Grade 10 to Grade 40. Buell Door Company's particleboard core doors qualify for Grade 40 Security Rating and provide a substantial material cost saving on the door price.
NOTE ** 7. Comparative substrate evaluations for Architectural Flush Door Core applications have shown structural composite lumber (SCL) such a TimberStrand LSL by Trus Joist MacMillan is equal to or better than stave core lumber in properties relevant to the performance of a flush architectural door. Therefore, it is warranted that it be recognized as an appropriate alternative core material for use in specifications that would historically specify stave core doors as set forth by the National Wood Window and Door Association in I.S.1.A and the 7th edition of the AWI Quality Standards, Section 1300.
NOTE ** Comparative tests have been done using two types of stave core, softwood (pine) and hardwood (aspen), along with TimberStrand LSL. Evaluations were made for strength and stiffness, screw holding, split resistance, and hinge holding. In all tests, the TimberStrand LSL with a target density of 38 pcf exceeded the performance level of traditionally used stave core products. Although comparable to stave lumber core in cost, TimberStrand LSL is superior in strength and the dimensional stability necessary to reduce telegraphing and warpage. For more detailed information on test results, contact Trus Joist MacMillan at 1-800-423-5808.
NOTE ** Eliminate stave core doors from your specs so the owner, general contractor, and manufacturer can jointly benefit by improved product quality and the monetary advantage in utilizing particleboard or structural composite lumber (SCL) core doors.
